Homeowner content is free. We may earn a commission when you click links through our site. Advertiser Disclosure

A blinking blue light on Google WiFi indicates that it is ready for initial setup. But if it is already set up in your case, it could mean the device is performing a factory reset or updating the firmware.

Irrespective of that, the blue light should ideally disappear in 10-15 minutes and turn into a solid white. However, it doesn’t, worry not. I will list all the possible causes and troubleshooting ways by which you can fix this problem quickly.

Google WiFi Solid Blue Light

Reasons Behind Google WiFi Flashing Blue & Ways To Fix It

  • Your WiFi point has no active internet connection.
  • The firmware update was incomplete or interrupted.
  • There's a random glitch or bug in the device or network.
  • Your WiFi node has lost power during the factory reset.
  • The device could not save/apply settings during the initial setup.

Now that you know the possible reasons that can create this issue, let's go through some tried and tested methods to fix it.

1. Restart Google WiFi

A simple restart can do more than you imagine. This is a simple troubleshooting step that anyone can try. The best part about this quick fix is that it will often resolve networking problems.

You can restart your Google WiFi using the Google Home app or do it manually. Both are pretty simple and can be done in a few seconds.

Using the app:

  • Open the Google Home app on your smartphone.
  • Head over to the WiFi section.
  • Tap on it and go to the settings.
  • Now tap on the restart network option.
  • Your Google WiFi device will now restart.
  • Wait till you see a solid white light on your Google WiFi.
  • If the pulsing blue persists, move to the next method.

Manual Restart:

Reset button on the Google Wifi
  • Remove the power cable of the WiFi device from the power socket.
  • Leave the device for about a minute.
  • Now plug it back in and let it restart automatically.
  • The router will take a couple of minutes to boot up properly.

2. Re-Configure WiFi Point

There could be an issue that occurred during the initial setup process that is leading to the blue blinking problem. Maybe the system could not save or apply settings during the setup process or any other issue that spoiled the setup.

The only way to fix it is by re-configuring the WiFi point. Note that you must follow a series of steps to properly set up the device. If you fail to perform any action or make any mistake, you must set it up again from scratch.

Steps to re-configure:

  • Download and install the Google Home app on your phone.
  • Plug in the ethernet cable to your WiFi point from the modem.
  • Now plug the power cord of the WiFi point into a power socket and wait for about a minute.
  • Now open the Google re-configuring phone.
  • Find the Add + icon and tap on it.
  • Select the setup device option and then the new device option.
  • Now the app will automatically find your Google WiFi point.
  • You have to tap on yes if it finds it.
  • Alternatively, you can also scan the QR code at your device's bottom to pair it up.

3. Power Cycle Internet Equipment

Sometimes, a restart isn’t enough to fix the issues on your internet equipment. You need to perform a power cycle to fix the mesh WiFi at times like this.

A power cycle will clear out the cache memory and temporary files and clear any temporary bugs/glitches. Performing it is not a difficult task, but it needs to be done in a specific manner.

Steps To Power Cycle All Internet Equipment:

  • Remove your Google WiFi point, modem, and other internet devices from the power source.
  • Now, wait for a couple of minutes.
  • Plug in back everything and turn them on.
  • Let the devices boot up properly. This will take 2-3 minutes.
  • Now check the status lights on Google WiFi and see if it's in an ideal state.

4. Check for Loose or Damaged Connection

A bad or loose connection has a high probability of Google WiFi point flashing in blue. To fix this, you need to check all your WiFi device's wired connections and ensure there are no loose ends. If found, fix it immediately or replace the whole cable and restart the WiFi device.

  • Unplug all the cables and plug them back in.
  • Cross-check for any physical damage on the cables.
  • Also, check for damage to ports or any water/dust deposition.
  • Use a different pair of cables and see if it works.
  • Use a different power socket.

5. Update Router Firmware

Faulty or outdated firmware can be a big reason for this issue. A firmware upgrade is required to improve the router's functionality and networking performance. You can avoid future problems by keeping your WiFi device up to date.

The firmware update should not take long, but if the LED light continues to flash for longer than expected, the firmware update is either stuck or there's a different matter causing the issue.

Steps to update:

  • Open the Google Home app on your phone.
  • Tap on your WiFi point.
  • Head over to the software information section.
  • Now tap on check for updates.
  • If there’s an update available, download and install it.
  • Let the Google WiFi point update itself.
  • This will take a couple of minutes.

Note: The router should not be turned off or disconnected from the power source during this process.

6. Factory Reset Google WiFi

Bad software or some recent changes in the settings can also be the reason. A simple restart cannot fix these, so a factory reset is required. A reset will fix most issues on the software side by bringing everything back to factory settings.

Note that your current customizations, username, and password data will be deleted. You must reconfigure your WiFi point once you've factory reset it.

Steps to reset:

Connect the internet cable to the WAN port
  • Ensure the WiFi device is on and connected to a power source.
  • Find the reset button located at the bottom of the device.
  • Press and hold the reset button for about 10 seconds.
  • The LED light will flash yellow and then change to solid blue.
  • Release the button when you see a blue light.
  • Now the WiFi point will begin the reset process.
  • This can take about 10 minutes.
  • Do not remove the device from the power source during this process.

Using the app:

Your google home app will look for the WiFi point
  • Open the Google Home app on your phone.
  • Tap and hold on to your device name.
  • Tap on settings on the top left.
  • Select factory reset WiFi point and then tap on factory reset to confirm.
  • Your device will not reset itself.

7. Contact Google Support

If you tried everything mentioned above and could not fix the issue, don’t worry. Not everything can be fixed by a common individual, and that’s why we have a support team. Reach out to them by clicking here, and they will help you troubleshoot.

You need to describe the issue in as much detail as you can and mindfully follow their instructions. If your device is under warranty, you can also claim a warranty and possibly get a replacement free of cost.

Frequently Asked Questions

Google WiFi flashing blue then orange: What to do?

If your Google WiFi flashes orange after blue, your device has been configured but does not have an active internet connection. Ensure you have plugged in the ethernet cable to the WAN port properly. Check if there is any service outage in your area.

Ideally, what light should stay on the Google WiFi point?

Under ideal conditions, you should see a solid white light on your Google WiFi point. This indicates that your WiFi device is working properly and has an active internet connection. Learn more.